There are many problems or failures that can occur on a computer when we want to establish a connection to the Internet. One of the most common on Windows computers is the “ does not have a valid IP configuration”.
Many of the users are not familiar with this type of problem, so it can be frustrating to solve it, especially if the person is not very knowledgeable about the subject. Nevertheless, It’s easier to fix than it seems.
If you got the error “Ethernet does not have a valid IP configuration” in Windows 10, don’t worry. We will help you through a detailed step by step guide how to fix it and enjoy your Internet connection.
What are the causes of the “Ethernet does not have a valid IP configuration” error?
It is very frustrating for many people who work with computers, not knowing how to solve a problem when it occurs and even more if it affects the Internet connection. In this sense, it is very common to encounter the error message of “Ethernet does not have a valid IP configuration”.
this notice means your private IP is invalid. Remember that the private IP is the one that is assigned to your team. So, the main cause of this error is due to a incorrect value in any of the following points:
- DNS
- The subnet mask of your team
- The gateway used
In case you don’t know how to fix it, you don’t have to worry. We will help you through a step-by-step guide how to make this error go away in windows 10 and you can proceed to enjoy your Internet service easily.
Steps to fix “Ethernet does not have a valid IP configuration” error in Windows 10
There are several methods that will allow you to get rid of the annoying “Ethernet does not have a valid IP configuration” error. The main ones are changing DNS, restarting the Winsock catalog, updating the controls of the equipment or restoring Windows to its old version.
Taking this into account, We will tell you about the steps to follow in each case:
Changing DNS
- Right-click on the icon located on the taskbar next to the clock, whose name is “Net”.
- Get in “Open Network and Sharing Center”.
- Select the network you are on and press the button “Properties”.
- go to “Internet Protocol version 4 (TCP/IPv4)” and select again “Properties”.
- In the box that you can see, select “Use the following addresses of the ” and write the following numbers: 8.8.8.8 Y 8.8.4.4.
- Lastly, click “Validate configuration on exit” and accept. Then wait for the execution network diagnosis and ready.
Restarts the winsock catalog
To restart winsock catalog it is necessary to first access the Windows command console as an administrator. For this, it must click start (It is located in the lower left corner of the screen, with the Windows icon). Then you have to write “cmd”.
Then it shows you the option to “Command Prompt”. Click on this option with the right mouse button and select “Execute as an administrator”. Once you are clear about this, apply the following steps:
- Disconnect the network cable to avoid any type of connection between the modem and your equipment with the damaged ethernet configuration.
- Go to the Windows command prompt and type netsh winsock reset and wait for Windows to perform the task.
- You will be prompted to restart your computer to save the changes. Finally, reconnect the network cable and the Internet should work normally.
Updating device drivers
First of all, you have to know how to update computer drivers in windows 10 It is done in the same way that other areas such as network adapters, printers, monitors, etc. are updated, that is, through installation by Windows Update.
To proceed with an efficient update, follow these steps:
- On the taskbar, type device manager and select “Device administrator”.
- Select a category for device names. Then right-click on the one you want to update.
- Click on “Search automatically for updated driver software”.
- Click on “Update driver” and ready.
In case Windows does not find a new driver, tWe recommend looking for one directly on the manufacturer’s website of the device and follow its instructions.
Restore Windows to a previous version
On some occasions, the error of “Ethernet does not have a valid IP configuration” after an update. In these cases, it is a good idea restore to a previous version. The correct way is indicated below:
- In the Windows Start menu, type “Control Panel”.
- Then click “Recovery”.
- After that, you must select in “Open”, “System Restore” and then in “Following”.
- Finally, choose the Restore Point you want to go back to and select “To finalize”.
I still have no Internet connection, what can I do in this case?
Despite having tried all the methods explained above, you may still have problems connecting to the Internet. We know that it is something very frustrating, so the best alternative in these cases would be communicate directly with the service provider.
The failure may come directly from the provider, so asking them for help is a good option. They are familiar with the subject and will be able to help you make this error go away.
Facebook Comments
Disqus