Currently the use of the Internet has become a necessity for all people, especially for big companies, in such a way that it is vital to have a good signal that covers all work or home areas. That is why today there are those who will help you to Internet coverage reaches those places where it did not before or its speed improves.
Due to all these problems, users find it necessary to look for equipment that helps them solve these problems, however, network amplifiers They are usually somewhat expensive and not all people have access to them. Because of all this, they have created home amplifiers which will also help you improve the performance of your Internet coverage.
That is why here we bring you some tricks so that you can create your own signal booster in a free way and that it really works. It is important to mention that you do not need to be an expert to be able to do this, you simply have to follow the steps that we will explain below and in a matter of minutes you will be able to have your own equipment to improve wireless internet signal in your living or workplace.
Steps and tricks to make a homemade Wi-Fi repeater antenna
The coverage of your wireless Internet It will depend a lot on the type of house, where it is located and the type of router you are using, any of these options can influence the coverage. These problems with the passage of time have been able to be solved thanks to the devices for improve WiFi signal.
Today there are different tricks and ways to create a signal amplifier yourself with which you will be able to solve this type of problem and Best of all, it will come out completely free of charge. since you will not need expensive materials to be able to do it.
In such a way that if you want to create your own home equipment you only have to follow the steps that we will explain below:
Home WiFi with a Can of Beer
This trick is one of the most common to do to try to improve the Internet signal in your home or office, With this method you will be able to create a repeat that will allow you to concentrate all WiFi coverage in a directional wayThis will allow you to direct the entire signal to where the devices you want to connect to the wireless network are located.
Keep in mind that the direction will be an imaginary line that you will draw from where is your router located to where the other devices you want to connect are.
In order to carry out this method it is necessary that you have the following materials on hand:
- An empty beer or soda can.
- Industrial scissors.
- Insulating tape
- A cutter.
How can you see all these materials can be obtained at home and generally do not have a high cost. For equipment manufacturing you have to follow these steps:
- The first thing you have to do is take the beer can and with the cutter you are going to cut the entire bottom part, the goal is to be able to remove the entire bottom of the can. In the event that it is easier for you with the scissors, you can also use them for this step.
- This same cut must be made in the top of the canbut this time you have to leave a piece of the can that is still attached to the rest of the container.
- Now very carefully and with the help of scissors you are going to cut the contour of the container from the bottom, in this way it will look like a cylindrical parabolic.
- We will place the top of the can as antenna basea, as indicated in the photo.
- Once this is done the WiFi repeater antenna will already be completed, it only remains to do the installation on the router.
- For this it will be necessary to use the tape to be able to fix it, preferably it is recommended to use the tin hole where does the drink come from insert the antenna and then you adjust it with the help of the tape.
It is important that before fixing the homemade antenna you have chosen the direction in which you want send the signal Once this is doneyour work will be finished.
Home WiFi with aluminum foil
This is another of the tricks that you will be able to use to improve the WiFi signal in your home, This method is not new, quite the contrary, it has been used for a long time and thanks to its good results it is still valid.
Currently, there are many users who for some reason have failures in their coverage, which causes them to have a bad signal or low speed. Due to this it has become popular the aluminum foil method, where its main function is route the wireless signal.
Surround the router with a beer can or aluminum foil It will help you reduce interference and thus create different barriers so that you can .
In order to carry out this method it is important that you have the following materials on hand:
- A card.
- Kitchen aluminum foil.
- Stick or liquid glue.
- Scissors to cut aluminum foil.
Once you have all the instruments ready, all that remains is to start with the manufacture of your signal antenna wireless internet. To do this you will follow these steps:
- The first thing you have to do is cut a cardboard the size of an A4 sheet.
- Once you have the rectangular figure cut out, you are going to cover with aluminum foilfor this you are going to use the glue and you must wait a few seconds for it to dry.
- It is important that you use another paper figure that you are going to glue to the rectangular one, you can also do it with cartulina and cover it with aluminum foil. You will use it to introduce router antenna and as support for the aluminum foil.
- Once all this is done, all that remains is to enter the antenna of the modem by the figure and your work will be done.
Create a homemade WiFi antenna with a Pringles can
This method is usually more complicated than the previous two. However, it is considered one of the best home wireless internet signal boosters. In this case, the main objective is to be able to replace the main antenna of the home router with a new homemade antenna, which will be made with a pringles can.
In this case, you are going to create a directional home antenna Therefore you must be sure which direction you want to give it, since it will point to a specific place.
If you want to perform this method it is important that you have the following materials on hand:
- A rod 140mm long and 3mm wide.
- 10 washers of 15 mm diameter.
- 10 nuts of 3 mm thread.
- 5 washers of 30 mm outer diameter and 6mm inner diameter.
- A pot of pringles potatoes of 170 grams.
- An adapter or USB key.
- A male-female USB extension cable of approximately 5 meters.
- A support, it can be plastic material.
- A cardboard lid.
Once you have all the materials ready and at hand, it only remains to start with the preparation of the homemade antenna for the wireless network, for this it is important that you perform the following steps:
- The first thing you are going to do is take the rod together with the washerswhich you are going to insert into the rod to form the figure that appears in pictures.
- This will serve to facilitate the receipt of frequency waves.
- At the time of insert the washers it is important to be very careful with the distance of each one of them, this will help the wave performs the parabola as best as possible. At the ends of the rod it will have two covers, one will be a plastic cover and the other will be a cardboard cover, both are used to support the equipment.
- The next thing will be to take the Pringles jar and open a hole on one of its sides, this has to be just the size of the usb wifi dongle so that it can be inserted and fit snugly.
- Once done you have to insert the rod with the washers through the pot of potatoes, To do this, you will first enter the cardboard lid, which will be the base of the container, while the plastic lid will be the main lid of the container.
- Once all this is done We introduce the USB flash drive to the container.
- Finally we create a support where the homemade Pringles antenna will gothis can be made of plastic, metal or the material that the user has on hand and can fulfill this function.
- Once all this is done, the manufacture of the antenna will be finishedit only remains to connect it to the modems and start using it to see its results.
A WiFi repeater using an old router
Today many users are still unaware that an old modem can be used as an access point plus increase the signal of the wireless network. In this way you will be able to improve the quality of coverage for free by simply using the equipment that you thought was no longer useful.
In order to create a new access point with an old router and to increase the WiFi signal, you need to have the following instruments:
- new router.
- old router.
- Ethernet cable.
- Computer.
Once you have these materials at hand, you simply have to follow the steps that we will explain below:
- To start you have to choose the place where you want locate the old router, keep in mind this one has to go plugged in and it has to be located between the main router and the area where you want increase WiFi signal.
- You have to use the ethernet network cable so you can unite both teams. (Not connected yet)
- Connect to power outlet the old modems near the computer and you have to reset it. Note that all of these teams have a bbutton on the back to perform this function.
- Now you have to join the old device with the ethernet cable with the computerthis will be only momentary, while the setting.
- Once they are connected you have to enter one of the browsers, in the search bar you will write the following address: so that you can enter the address of the router.
- In the event that an error message appears, try this address: 192.168.1.2
- A window will appear on the screen asking you to enter username and password, you must look for it in the equipment manual, in one of the stickers of the equipment or in its box. If it doesn’t appear you can try Admin/admin or admin/1234.
- After having accessed the you have to create a new WiFi network, write down the name and password you choose.
- The next thing will be to access the configuration of the Red lan. Here you have to review the IP addressif the main team has 192.168.1.1 you can assign the address to the old device 192.168.1.2.
- Now check that the option is activated Enable DHCP Server Relay or similar. And finally you are going to save the changes.
- Disconnect the cable and with a mobile or a laptop you will check that it is detected the new wifi network that you have created
- reconnect the cable to the computer and again enter the configuration of the equipment by repeating the previous steps.
- When you have entered again you will look for the section of the dhcp server.
- There you have to make sure that it appears disconnected, if it is not, disconnect it or deactivate the “Server…
Facebook Comments
Disqus