【 +10 Heat Sinks for Raspberry Pi 】 List ▷ 2022

Electronic devices like computers or boards always run the risk of suffer overheatingespecially when your processor temperature is at maximum load.

And it is that one high temperature in these teams can cause different failures in the operation of the samebut when it exceeds the limit damage may result irreparable.

One way to try to counter this is through a heat sink or since they provide a Essential cooling for the hob. That is why here we are going to show you the best heatsinks that you can install on your .

What are heat sinks and what are they for on a Raspberry Pi?

Heat sinks are a metallic device that they lead and dissipate or disperse excess heat that is generated by an electronic component or a power source. Therefore, they are in charge of promoting a method of conductivity cooling thermal and these can be used in any electronic device and can mostly be seen in CPUalso known as processors or microprocessorsas well as in the .

They are highly important because The high temperatures reached by the components of this equipment can burn them completely. Thus, the main function of a heat sink is to absorb it and remove it by dissipation of the box or casing of the computer. To guarantee its correct operation it is important that it has a good thermal contact with electronic components.

Mainly these heat sinks are accompanied by a fan in order to increase air flow and use a type of adhesive or thermal paste, which will facilitate the transfer of heat from the electronic component to the outside. In the case of Raspberry Pi Its two main components must be ensured, such as the CPU and chip.

Although it should be mentioned that heat sinks are mostly not essential, in the case of Raspberry Pi If they are used for basic use, they will not generate much heat, so the components will not be affected, which is why the basic version of these boards come without heatsink because they don’t think it’s necessary. But despite not being completely necessary, it is not bad or else that you want to install one on it.

Keep in mind that the heatsinks can be of anodized or copper aluminumIn this case, the former are usually much cheaper and less heavy, while the copper ones are the opposite. Finally, we are going to show you an example of all the components of the plate and where a greater heat is concentrated in it, this was seen through a thermal camera that allows to highlight hottest spots. The red dots are high temperatures and the blue ones are low.

According to what is shown in these images you can see which are the two areas most affected by overheating on the plate, so they are the two points or areas that must be protected. This is the processor that is in the center of the board and is the most visible and the Chip Lan located on the right and you can see that it also produces a lot of heat.

List of the best heat sinks that you can use in your Raspberry Pi single board computer

As already mentioned above Raspberry Pi comes from the factory without a heat dissipatorbut currently you can find several of them that work very well with this board and that you could use if you want to have greater security or mainly if you spend a lot of time working on the plate.

That is why we are going to show you a list of the best heat sinks that you can buy today:

GeeekPi Raspberry Pi 3 B+

This heat sink has been created to be used with the Pi 3B+ model, which will offer a box with fan and heat sinkit will prevent the components of this model from reaching overheat while you are using it.

In this way you will have access to all the ports of the Raspberry Pi board, it is a very good quality transparent acrylic and with blue ABS materials and has a 2-pin cooling fan and heat sinks to achieve a better dissipation of the same towards the outside.

Geeekpi Armor Case

It is only available for the version of Raspberry Pi 3B+, Therefore, it offers a case with a heatsink that uses CNC machining manufacturing technology to offer a aluminium alloy. In the same way, it has three (3) small terminals that offer better heat dissipation from the board.

Have USB port, HDMI, GPIO, Ethernet interface, power jack, A/V port, display interface, camera interface and micro SD card slot, all these components are accessible from the box. Finally, it should be mentioned that this ventilation casing It is created by aluminum alloy, 3x heat tape, 1 sets of screws and a manual of facility to make this job easier for users.

For Raspberry Transparent Box

It is a box that has a 5V / 2.5ª charger + 3 x heatsink + fan + micro USB cable with connector off and on. It should be mentioned that this case has a better transition design than the one already mentioned and said case consists of 9 individual high-quality layers and 4 nylon screws to assemble it without the need for a tool.

Some of the main features include the following:

It is a perfect combination to be used for Raspberry Pi 3 model b+ b.
It is very easy to use thanks to the 9 individual layers it has.
Thanks to the fan that it has, you can quickly reduce the temperature of the CPU chip without overheating.
By having three heat sinks for the Raspberry Pi Allows for better ventilation CPU/ LAN/ RAM, where it just removes the stickiness from the back of the heat sink.
It is available only for Pi 3B+ boards
It has different ports such as those of the micro SD card easy access, HDMI cables, insert/drop cables.

Geekpi for Raspberry Pi

This is the latest version of 9 layer acrylic box and which has a very good appearance. It has a fan, charger 5V/ 2.5 A with on/off connector. This heat sink offers greater compatibility with these plates, this is how it is available for the 2B/ 3B/ 3B+ models.

Some of its most important characteristics are the following:

This box allows access to all the ports of the raspberry pi board as are the USB, GPIO, HDMI ports and the groove of the microSD card.
Their cooling fan and heat sinks They are of very good quality so they can dissipate heat from the plate very easily.
Its power supply is 5V 2.5 A with a TUV and CE certification. The cable length with on/off switch is 100cm and offers a micro USB plug.
All this package will include 1 9-layer acrylic case, 1 cooling fan, 3 pieces of heat sinks, screws and screwdrivers.

For Raspberry Pi 3B+

This box has a better classic design so it offers a fan with 3 heatsinks for Pi case that will allow you to reduce the temperature quickly no matter how high it is. It is compatible with Pi models 3 2 model B+.

Some of the most outstanding characteristics are the following:

It is an updated version so it has a almost perfect box that you will be able to assemble it without the need for tools.
It offers a double refrigeration system with a fan and 3 heatsinks for Pi case.
Offers a great speed to lower the temperature.
Offers multiple ports, easy access to the SD card and insert and remove the breakout cable and HDMI cable.
It has a USB cable with ON/OFF connector.
It has protection for overload and short circuits.

For Raspberry Modular

This box has 3 heatsinks for Pi 3 Y a fanwhich have the ability to reduce any overheating of the plate quickly and significantly improves the ventilation of Ian/ ram chips and cpu.

Some of its most important features include the following:

It offers an updated version that is perfect for the models of the Raspberry Pi 3 2 model B+.
Your box is made up of 9 individual layers and uses 4 metal screws to be able to assemble it without the need for tools.
It has a double cooling system with a fan and 3 heatsinks for raspberry pi 3kit, allowing the temperature to drop quickly.
This case features multiple ports and easy access to micro card SDas well as for the HDMI cable.
It has a 1.5 m charger cable with off and on.
It has short circuit protection and overload protection.

Raspberry Pi 4

This heat sink fan for raspberry pi boards is available for several versions as it is the Pi 3 B+, Pi 3b, Pi 2 and Pi 4 and for many other single board computers. Therefore, it will help you maintain the optimal temperature of your microcomputer every time you work on it.

It has the following characteristics:

It offers a cheaper price than those heatsinks that it has two fans and a fan.
It is compatible with a large number of single board computersso it offers many possibilities of use.
Thanks to the heat sink it is possible to maintain a efficient temperature.
The custom 3M thermal strips they are able to ensure that your board works stably.
The updates of the fan bearing not only guarantees that there is blown wind, but it is also very quiet so you will not have a noise problem.

Seed Studio

It is a heatsink developed by Seed Studiowhich is characterized by being very simple and is composed of a copper heat pipe and a 40mm fan, which is in charge of pushing the air through its cooling fins. In addition, it should be noted that it has a very simple anchoring system.

It uses four data carriers, which are very similar to those used by desktop computers to ensure the motherboard to the box. All this allows through the Raspberry Pi 4 PCB, a fairly secure connection can be created. Thus, it can be said that it is a anchoring the heatsink to the processor and PCB. If you have some experience, being able to mount this heat sink on your motherboard will not be a problem.

Adafruit Miniature 5V Cooling fan for Raspberry Pi

Is about a 5V mini cooling fan, It is ideal for those users who work for long hours in their raspberrypi, so they can prevent these from overheating. In addition, it offers great compatibility with different equipment, making it ideal for any microcomputer or any other device that needs cooling.

For this one…